Rugged-ridge RRC Rear Bumper, 2-Inch Hitch & Tire Carrier, Instrukcja Użytkownika Pobierz pdf

Rugged Ridge

Rock Crawler Rear Bumper

P/N: 11503.13 - 14

Installation Instructions.

Can be used for tires sizes up to 35"

Components - Box 1 Components - Box 2 (tire carrier)

(Box 1):

(1) Rock Crawler rear bumper (box 1)

(Box 2):

(1) Tire Carrier with latch installed

(10) M12 - 1.75 x 30mm Hex Head Bolt (1) Post Bar

(8) M12 Nylock Nuts (1) Tire Mount

(18) M12 Flat Washers (1) c45 Circle Clip

(10) M12 Lock Washers (3) 3/8"-24 x 1" Hex Head Bolt

(2) 3/8"-24 x 1 1/4" Hex Head Bolt

(8) 3/8" Flat Washers

(5) 3/8" Nylock Nuts

(1) 3/8" - 16UNC X 67 Round Cross Bolt

(4) c10 Washers

(1) 3/8" Nylock Nut

(1) Rubber Bushing/Spacer

(1) Nylon Washer

(1) ST6.3 x 25 Phillips Head Screw

NOTE: TWO PEOPLE WILL BE NEEDED TO MOUNT THIS BUMPER.

(Step 1):

Remove original factory bumper per manufacturer's instructions. The lower mounting bolts

can be reused if desired.

(Step 2):

The inner mounting holes on the Rock Crawler bumper will not align with any factory holes

regardless of model year (Fig.1). With the help of another person mount the bumper using the

outer holes only. With bumper secured scribe or mark the inner hole locations. (Fig.2)

Be sure to mark hole location correctly for proper fitment. Remove bumper and set aside.

Fig.1

Fig.2

(Step 3):

With the holes marked or scribed drill a small 3/16" pilot hole in the rear cross member in the

center of your marks. The smaller pilot hole insures the centering of your larger mounting

hole when drilled.

CAUTION: EXTREME CARE SHOULD BE TAKEN BEFORE DRILLING.

THE FUEL TANK IS LOCATED JUST BEHIND THE CROSS MEMBER.

Great care will be

needed to avoid damaging the fuel tank.

With the smaller 3/16" pilot holes drilled, enlarge the holes using a 1/2" drill bit.

AGAIN, BE CAREFUL AND AVOID ANY CONTACT OF THE DRILL BIT TO FUEL TANK.

Pg.1

1 2 3

PRODUCT WARRANTY 3

Podsumowanie treści

Strona 1

Rugged Ridge Rock Crawler Rear BumperP/N: 11503.13 - 14Installation Instructions.Can be used for tires sizes up to 35"Components - Box 1

Strona 2

(Step 4):With mounting holes drilled reposition bumper back to frame cross member and secure using(6) M12 x 30mm Hex Head Bolts, (12) M12 Flat Washers

Strona 3 - PRODUCT WARRANTY

(Step 8): Install Post Bar at this time to the top of the tire carrier. Use (1) 3/4" x 3" Hex Head Bolt,(2) 3/4" Flat Washers, and (1)

Komentarze do niniejszej Instrukcji

Brak uwag

Rugged-ridge RRC Rear Bumper, 2-Inch Hitch & Tire Carrier, Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Do samochodu Rugged-ridge RRC Rear Bumper, 2-Inch Hitch & Tire Carrier, . Rugged Ridge RRC Rear Bumper, 2-Inch Hitch & Tire Carrier, 87-06 Jeep Wrangler User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Do samochodu Rugged-ridge RRC Rear Bumper, 2-Inch Hitch & Tire Carrier,